Electric Servo Press Systems: Structure, Control and Assembly Uses

2026-11-17 Technical Insights

Introduction

An electric servo press is a CNC-controlled press unit that uses a servo electric cylinder to generate controlled force and displacement during assembly operations. Unlike conventional hydraulic or pneumatic presses, an electric servo press integrates motion control, force and displacement measurement, and process monitoring into a single system, making each pressing cycle measurable and repeatable.

In automotive manufacturing and industrial assembly, press fitting operations such as bearing installation, bushing insertion, riveting, and component forming require consistent force application and verifiable results. An electric servo press addresses these requirements by providing programmable pressing profiles, real-time process detection, and data traceability that can be integrated with production control systems.

This article examines the structure of electric servo press systems, their control architecture, key performance characteristics, and typical assembly applications, with reference to the N-Series Servo Press Fitting System as an example of a modular servo press design.

Product Overview

The N-Series Servo Press Fitting System is a high-precision CNC press unit designed for automated assembly and manufacturing applications. It integrates servo motion control, force and displacement measurement, process monitoring, and production data management. The system is intended for precision assembly in automotive manufacturing and industrial production lines where stable, repeatable, and traceable press fitting processes are required. For more product details, see the N-Series Servo Press Fitting System.

The system is available in multiple force configurations ranging from 2 kN to 350 kN, allowing selection according to the force requirements of specific assembly tasks. This range covers applications from low-force precision assembly to high-force industrial pressing.

Working Principle

An electric servo press generates pressing force through a servo electric cylinder rather than hydraulic fluid or compressed air. The servo motor drives the press rod, and the system continuously measures both force and displacement throughout the pressing cycle. This integrated measurement allows the press to operate in different control modes:

  • Force-controlled pressing: The system applies a defined force profile, with displacement resulting from the material response.

  • Displacement-controlled pressing: The system moves the press rod to a defined position, with force resulting from the material resistance.

  • External signal-based control: Pressing sequences can be triggered or modulated by signals from external equipment or line controls.

Because force and displacement are measured continuously, each pressing cycle produces a force-displacement curve that can be evaluated against defined criteria. The system's sampling frequency of 20 kHz and 24-bit acquisition accuracy support detailed process monitoring.

System Structure

The N-Series Servo Press Fitting System adopts a modular architecture. Each module performs a specific function and works together to provide motion control, process monitoring, and data acquisition. The modular design allows the system to be integrated into automated assembly equipment and automotive production lines. KINMARK also provides dedicated press fitting functional modules for different equipment configurations and integration requirements.

Servo Electric Cylinder

The servo electric cylinder is the mechanical core of the press. It features a high-strength mechanical construction for stable operation in demanding industrial environments. An integrated pressure sensor provides force measurement for real-time process monitoring. The anti-torsion press rod can be directly connected to press tooling, simplifying integration into automated assembly equipment.

E-Press Industrial Software

E-Press industrial software provides an interface for programming, monitoring, and evaluating press fitting processes. Operators can monitor process curves and assembly results in real time. Key software functions include:

  • Real-time force-displacement curve display

  • Real-time force-time curve display

  • Multiple pressing steps and process curves

  • Judgment window and envelope curve evaluation

  • Measurement and OK/NG result evaluation

  • Hierarchical user permission management

  • Press fitting history and operation logs

  • Alarm log management

  • Support for MS SQL and Microsoft Access databases

Control Box, Monitoring Instrument and Cable Module

The control box, monitoring instrument, and cable module complete the system by providing the electrical and communication infrastructure for motion control, measurement, and data exchange. The system supports fieldbus communication including OPC, EtherNet/IP, and PROFINET, allowing integration with PLCs and production servers.

Key Features

  • High-precision servo control: Force accuracy up to 1% FS and position accuracy up to 0.01 mm.

  • Integrated force and displacement measurement: Continuous measurement throughout the assembly process with 20 kHz sampling frequency and 24-bit acquisition accuracy.

  • Flexible process control: Force-controlled, displacement-controlled, and external signal-based pressing modes.

  • Real-time process detection: 100% process monitoring of each pressing cycle to detect deviations and maintain consistent assembly quality.

  • Process data traceability: Measurement data and assembly results can interact with PLCs and production servers for process data recording and traceability.

  • Multiple evaluation functions: Judgment windows, envelope curves, and measurement analysis support different pressing requirements.

  • Wide force range: Available in configurations from 2 kN to 350 kN.

  • Modular system architecture: Servo electric cylinder, industrial software, control box, monitoring instrument, and cable module for flexible integration.

  • Durable construction: Service life exceeding 12 million cycles, IP54 protection rating, and noise below 75 dB.

Technical Specifications

The N-Series Servo Press Fitting System is available in multiple force configurations. The following table summarizes the main specifications by model.

ModelStroke (mm)Maximum Pressure (kN)Running Speed (mm/s)Force AccuracyPosition Accuracy (mm)
2KN100–20020.02–2601%FS0.01
5KN100–20050.02–2601%FS0.01
10KN100–400100.02–2501%FS0.01
20KN100–400200.02–1251%FS0.01
30KN200–400300.02–2001%FS0.01
50KN200–400500.02–2001%FS0.01
80KN300–400800.02–1601%FS0.01
100KN300–4001000.02–1401%FS0.01
150KN200–4001500.02–1401%FS0.01
200KN200–4002000.02–1001%FS0.01
350KN200–4003500.02–501%FS0.01

General specifications include position accuracy ≤ 0.01 mm, force control accuracy ≤ 1% FS, maximum pressure holding time of 3 s, noise below 75 dB, service life exceeding 12 million cycles, and IP54 protection rating. The system supports fieldbus communication via OPC, EtherNet/IP, and PROFINET. Rated power ranges from 0.2 to 14.5 kW at 50/60 Hz, with rated voltage options including single-phase 220 V, three-phase 220 V, or three-phase 380 V depending on the model. The operating environment is 0–50°C and 10–90% RH non-condensing. Supported languages are Chinese and English, and output formats include CSV and XLS.

Note: Specifications may vary depending on the product model. Please refer to the actual product configuration.

Applications

Electric servo press systems are used in a range of assembly and manufacturing operations. The N-Series system is suitable for the following applications:

  • Press fitting and component assembly: Controlled insertion of bearings, bushings, seals, and other components.

  • Automotive component assembly: Precision pressing operations in powertrain, chassis, and other automotive component manufacturing.

  • Forming and riveting: Controlled deformation and riveting processes requiring defined force and displacement.

  • Punching operations: Punching tasks where force and position control are required.

  • Elasticity and performance testing: Measurement of component response under controlled force or displacement.

  • High-cycle automated assembly: Repeated pressing operations integrated into automated production lines.

The system is designed for integration with PLCs, industrial control systems, and production servers, making it suitable for automotive assembly lines that require high repeatability, quality control, and process traceability. For more complex automated assembly requirements, KINMARK also offers press fitting workstations.

Benefits

Electric servo press systems offer several practical benefits for manufacturing operations:

  • Improved process consistency: Servo control and continuous force-displacement measurement help maintain stable and repeatable pressing results.

  • Enhanced traceability: Measurement data and assembly results can be recorded and exchanged with production systems, supporting process documentation.

  • Flexible integration: The modular architecture and fieldbus communication options allow integration into automated assembly equipment and production lines.

  • Real-time quality monitoring: 100% process monitoring of each cycle enables detection of process deviations as they occur.

  • Reduced dependence on operator judgment: Programmable pressing profiles and automated evaluation functions support consistent decision-making.

  • Wide application coverage: Multiple force configurations from 2 kN to 350 kN address different assembly requirements.

Why Choose KINMARK

KINMARK (Jinan Zhongzheng Jinma Technology Co., Ltd.) has been engaged in automotive intelligent automation equipment since 1996. The company develops and manufactures marking and traceability systems, servo press systems, fluid filling systems, and robot automation systems. Its servo press systems are part of a product portfolio serving automotive manufacturing, automotive components, new energy vehicles, powertrain manufacturing, and intelligent factory automation. Learn more about KINMARK's servo press fitting solutions.

KINMARK has established long-term cooperation with automotive manufacturers and suppliers, and provides installation, commissioning, operator training, and after-sales support. The N-Series Servo Press Fitting System is covered by a 12-month warranty, with remote diagnosis and technical assistance available to support continuous operation.

Frequently Asked Questions

What is the difference between an electric servo press and a hydraulic press?

An electric servo press uses a servo electric cylinder to generate force, with integrated force and displacement measurement throughout the pressing cycle. This allows programmable pressing profiles and real-time process monitoring. Hydraulic presses use hydraulic fluid pressure and typically do not provide the same level of integrated measurement and data traceability.

What force range is available in the N-Series Servo Press Fitting System?

The N-Series is available in configurations from 2 kN to 350 kN, covering applications from low-force precision assembly to high-force industrial pressing.

Can the servo press system be integrated with existing production lines?

Yes. The system supports fieldbus communication including OPC, EtherNet/IP, and PROFINET, and can be integrated with PLCs, industrial control systems, and production servers. The modular architecture allows integration into automated assembly equipment and automotive production lines.

What data can be recorded during pressing?

The system records force and displacement measurement data and assembly results. Data can be exchanged with PLCs and production servers, and output formats include CSV and XLS. The E-Press software supports press fitting history, operation logs, and alarm log management.

What is the position accuracy of the N-Series servo press?

The N-Series Servo Press Fitting System provides position accuracy up to 0.01 mm and force accuracy up to 1% FS across its force configurations.

Conclusion

Electric servo press systems combine servo motion control, force and displacement measurement, and process data management to support precise, repeatable, and traceable press fitting operations. The modular architecture, multiple force configurations, and integration capabilities of the N-Series Servo Press Fitting System make it suitable for automotive assembly and industrial production applications where process consistency and quality documentation are important. As manufacturing operations continue to emphasize traceability and automation, electric servo press systems provide a practical solution for controlled assembly processes.


If you're interested in any of the equipment mentioned in this article, feel free to contact our sales engineers for detailed product information and customized technical solutions.